Loading...
29 results
Search Results
Now showing 1 - 10 of 29
- Microalgal-based industry vs. microplastic pollution: Current knowledge and future perspectivesPublication . Mendonça, Ivana; Faria, Marisa; Rodrigues, Filipa; Cordeiro, NereidaMicroalgae can play a crucial role in the environment due to their efficient capture of CO2 and their potential as a solution for a carbon-negative economy. Water quality is critical for the success and profitability of microalgal based industries, and understanding their response to emergent pollutants, such as microplastics (MPs), is essential. Despite the published studies investigating the impact of MPs on microalgae, knowledge in this area remains limited. Most studies have mainly focused on microalgal growth, metabolite analysis, and photosyn thetic activity, with significant discrepancies in what is known about the impact on biomass yield. Recent studies show that the yield of biomass production depends on the levels of water contamination by MPs, making it necessary to reduce the contamination levels in the water. However, present technologies for extracting and purifying water from MPs are limited, and further research and technological advancements are required. One promising solution is the use of bio-based polymer materials, such as bacterial cellulose, which offer biode gradability, cost-effectiveness, and environmentally friendly detoxifying properties. This review summarises the current knowledge on MPs pollution and its impact on the viability and proliferation of microalgae-based industries, highlights the need for further research, and discusses the potential of bio-solutions for MPs removal in microalgae-based industries.
- From a basic microalga and an Acetic Acid Bacterium cellulose producer to a living symbiotic biofilmPublication . Nóbrega, Vítor; Faria, Marisa; Quintana, Antera; Kaufmann, Manfred; Ferreira, Artur; Cordeiro, Nereida Maria AbanoBacterial cellulose (BC) has recently been the subject of a considerable amount of research, not only for its environmentally friendly biosynthesis, but also for its high potential in areas such as biomedicine or biomaterials. A symbiotic relationship between a photosynthetic microalga, Chlamydomonas debaryana, and a cellulose producer bacterium, Komagataeibacter saccharivorans, was established in order to obtain a viable and active biofilm. The effect of the growth media composition ratio on the produced living material was investigated, as well as the microalgae biomass quantity, temperature, and incubation time. The optimal temperature for higher symbiotic biofilm production was 30 °C with an incubation period of 14 days. The high microalgae presence, 0.75% w/v, and 60:40 HS:BG-11 medium (v/v) induced a biofilm microalgae incorporation rate of 85%. The obtained results report, for the first time, a successful symbiotic interaction developed in situ between an alkaline photosynthetic microalga and an acetic acid bacterium. These results are promising and open a new window to BC living biofilm applications in medical fields that have not yet been explored.
- Lipid and fatty acid composition of wild Almaco Jack Seriola rivoliana at two maturation stagesPublication . Fernandes, Igor; Nogueira, Natacha; Faria, Graça; Fernandes, Tomásia; Faria, Marisa; Cordeiro, NereidaAlmaco jack (Seriola rivoliana) is an emergent marine finfish that presents high market value. In order to study the feasibility of the exploitation of this marine resource for human consumption the evaluation of the nutritional characteristics of this species has attracted the attention of the scientific community. The lipid characteristics and fatty acid composition were evaluated in muscle, liver and gonad tissues of wild Almaco jack from Atlantic Ocean at two different maturation stages. According to results, the lipid content was found higher at pre-spawning stage (21.78 - 36.17%) and highest proportion being exhibited in the liver. Palmitic acid was predominant among the saturated fatty acids (35.42 - 47.80%) and oleic acid was detected as the main monounsaturated acid (25.26 - 36.55%). Higher amounts of ω3 polyunsaturated fatty acids (PUFAs) were identified in gonads of resting females, of which more than 84% was accounted by docosahexaenoic acid (12.62%). Muscle and liver of resting females presented the highest ω3/ω6 ratios. The Hypocholesterolemic/Hypercholesterolemic index was higher in gonads of both maturation stages (0.97 and 1.05). The results showed that wild Almaco jack at resting stage were a better source of oleic acid and ω3 PUFAs and that liver and gonads present good nutritional by-products.
- In situ biosynthesis of bacterial nanocellulose-CaCO3 hybrid bionanocomposite: one-step processPublication . Mohammadkazemi, Faranak; Faria, Marisa; Cordeiro, NereidaIn this work, a simple and green route to the synthesis of the bacterial nanocellulose-calcium carbonate (BNC/CaCO3) hybrid bionanocomposites using one-step in situ biosynthesis was studied. The CaCO3 was incorporated in the bacterial nanocellulose structure during the cellulose biosynthesis by Gluconacetobacter xylinus PTCC 1734 bacteria. Hestrin-Schramm (HS) and Zhou (Z) culture media were used to the hybrid bionanocomposites production and the effect of ethanol addition was investigated. Attenuated total reflection Fourier transform infrared spectroscopy, field emission scanning electron microscopy, X-ray diffraction, energy-dispersive X-ray spectroscopy, inverse gas chromatography and thermogravimetric analysis were used to characterize the samples. The experimental results demonstrated that the ethanol and culture medium play an important role in the BNC/CaCO3 hybrid bionanocomposites production, structure and properties. The BNC/CaCO3 biosynthesized in Z culture medium revealed higher O/C ratio and amphoteric surface character, which justify the highest CaCO3 content incorporation. The CaCO3 was incorporated into the cellulosic matrix decreasing the bacterial nanocellulose crystallinity. This work reveals the high potential of in situ biosynthesis of BNC/CaCO3 hybrid bionanocomposites and opens a new way to the high value-added applications of bacterial nanocellulose.
- Poly(glycidyl methacrylate)/bacterial cellulose nanocomposites: preparation, characterization and post-modificationPublication . Faria, Marisa; Vilela, Carla; Mohammadkazemi, Faranak; Silvestre, Armando J.D.; Freire, Carmen S. R.; Cordeiro, NereidaNanocomposites composed of poly(glycidyl methacrylate) (PGMA) and bacterial cellulose (BC) were prepared by the in-situ free radical polymerization of glycidyl methacrylate (GMA) inside the BC network. The resulting nanocomposites were characterized in terms of structure, morphology, water-uptake capacity, thermal stability and viscoelastic properties. The three-dimensional structure of BC endowed the nanocomposites with good thermal stability (up to 270 °C) and viscoelastic properties (minimum storage modulus = 80 MPa at 200 °C). In addition, the water-uptake and crystallinity decreased with the increasing content of the hydrophobic and amorphous PGMA matrix. These nanocomposites were then submitted to post-modification via acid-catalysed hydrolysis to convert the hydrophobic PGMA into the hydrophilic poly(glyceryl methacrylate) (PGOHMA) counterpart, which increased the hydrophilicity of the nanocomposites and consequently improved their water-uptake capacity. Besides, the post-modified nanocomposites maintained a good thermal stability (up to 250 °C), viscoelastic properties (minimum storage modulus = 171 MPa at 200 °C) and porous structure. In view of these results, the PGMA/BC nanocomposites can be used as functional hydrophobic nanocomposites for post-modification reactions, whereas the PGOHMA/BC nanocomposites might have potential for biomedical applications requiring hydrophilic, swellable and biocompatible materials.
- Conductive bacterial cellulose-polyaniline blends: Influence of the matrix and synthesis conditionsPublication . Alonso, Emanuel; Faria, Marisa; Mohammadkazemi, Faranak; Resnik, Matic; Ferreira, Artur; Cordeiro, NereidaBacterial cellulose/polyaniline (BC/PANi) blends present a great potential for several applications. The current study evaluates the impact of using different BC matrixes (drained, freeze-dried and regenerated) and different synthesis conditions (in situ and ex situ) to improve the inherent properties of BC, which were monitored through FTIR-ATR, EDX, XRD, SEM, AFM, swelling, contact angle measurement and IGC. The employment of in situ polymerization onto drained BC presented the most conductive membrane (1.4 × 10-1 S/cm). The crystallinity, swelling capacity, surface energy and acid/base behavior of the BC membranes is substantially modified upon PANi incorporation, being dependent on the BC matrix used, being the freeze-dried BC blends the ones with highest crystallinity (up to 54%), swelling capacity (up to 414%) and surface energy (up to 75.0 mJ/m2). Hence, this work evidenced that the final properties of the BC/PANi blends are greatly influenced by both the BC matrixes and synthesis methods employed.
- Microplastics reduce microalgal biomass by decreasing single-cell weight: the barrier towards implementation at scalePublication . Mendonça, Ivana; Cunha, César; Kaufmann, Manfred; Faria, Marisa; Cordeiro, NereidaMicroplastics (MPs) are a widespread environmental threat, especially to aquatic and urban systems. Water quality is vital for biomass production in microalgal-based industries. Here, industrially relevant microalgae Tetraselmis suecica, Scenedesmus armatus, and Nannochloropsis gaditana were exposed to PS- and PE-MPs (polystyrene and polyethylene, re spectively – 10-20 μm) contaminated waters (5 and 10 mg/L). Following industrial empirical and ecotoxicological pro cedures, the production period was established as four days (exponential growth phase). 27-long day experiments were conducted to determine the chronic effects of MPs contamination in microalgal biomass yields. MPs induced different responses in cell density: T. suecica decreased (up to 11 %); S. armatus showed no changes; and N. gaditana increased (up to 6 %). However, all three microalgae exhibited significant decreases in biomass production (up to 24, 48, and 52 %, respectively). S. armatus exposed to PS-MPs and N. gaditana exposed to PE-MPs were the most im pacted regarding biomass production. The decrease in biomass yield was due to the reduction in single-cell weight (up to 14, 47, and 43 %), and/or the production of smaller-sized cells (T. suecica). In response to chronic exposure, microalgae showed signs of cell density adaptation. Despite cell density normalizing, biomass production was still re duced compared to biomass production in clean water. Computational modelling highlighted that MPs exposure had a concentration-dependent negative impact on microalgae biomass. The models allow the evaluation of the systematic risks that MPs impose in microalgal-based industries and stimulate actions towards implementing systems to contain/ eliminate MPs contamination in the waters used in microalgae production.
- New bacterial cellulose nanocomposites prepared by in situ radical polymerization of methacrylate monomersPublication . Faria, Marisa Camacho Gonçalves; Cordeiro, Nereida Maria Abano; Barros, Carmen Sofia da Rocha FreireBacterial cellulose/polymethacrylate nanocomposites have received attention in numerous areas of study and in a variety of applications. The attractive properties of methacrylate polymers and bacterial cellulose, BC, allow the synthesis of new nanocomposites with distinct characteristics. In this study, BC/poly(glycidylmethacrylate) (BC/PGMA) and BC/poly(ethyleneglycol)methacrylate (BC/PPEGMA) nanocomposites were prepared through in situ free radical polymerization of GMA and PEGMA, respectively. Ammonium persulphate (APS) was used as an initiator and N,N’methylenebisacrilamide (MBA) was used as a crosslinker in BC/PGMA. Chemical composition, morphology, thermal stability, water absorption, mechanic and surface properties were determined through specific characterization techniques. The optimal polymerization was obtained at (1:2) for BC/PGMA, (1:2:0.2) ratio for BC/GMA/MBA and (1:20) for BC/PPEGMA, with 0.5% of initiator at 60 ºC during 6 h. A maximum of 67% and 87% of incorporation percentage was obtained, respectively, for the nanocomposites BC/PGMA/MBA and BC/PPEGMA. BC/PGMA nanocomposites exhibited an increase of roughness and compactation of the three-dimensional structure, an improvement in the thermal and mechanical properties, and a decrease in their swelling ability and crystallinity. On the other hand, BC/PPEGMA showed a decrease of stiffness of three-dimensional structure, improvement in thermal and mechanical properties, an increase in their swelling ability and a decrease the crystallinity. Both BC/polymethacrylate nanocomposites exhibited a basic surface character. The acid treatment showed to be a suitable strategy to modifiy BC/PGMA nanocomposites through epoxide ring-opening reaction mechanism. Nanocomposites became more compact, smooth and with more water retention ability. A decrease in the thermal and mechanical proprieties was observed. The new nanocomposites acquired properties useful to biomedical applications or/and removal of heavy metals due to the presence of functional groups.
- Solving urban water microplastics with bacterial cellulose hydrogels: leveraging predictive computational modelsPublication . Mendonça, Ivana; Sousa, Jessica; Cunha, César; Faria, Marisa; Ferreira, Artur; Cordeiro, NereidaThe prevalence of microplastics (MPs) in both urban and aquatic ecosystems is concerning, with wastewater treatment plants being considered one of the major sources of the issue. As the focus on developing sustainable solutions increases, unused remnants from bacterial cellulose (BC) membranes were ground to form BC hydrogels as potential bioflocculants of MPs. The influence of operational parameters such as BC:MPs ratio, hydrogel grinding, immersion and mixing time, temperature, pH, ionic strength, and metal cations on MPs flocculation and dispersion were evaluated. A response surface methodology based on experimental data sets was computed to understand how these parameters influence the flocculation process. Further, both the BC hydrogel and the hetero-aggregation of MPs were characterised by UV–Vis, ATR-FTIR, IGC, water uptake assays, fluorescence, and scanning electron microscopy. These highlights that the BC hydrogel would be fully effective at hetero aggregating MPs in naturally-occurring concentrations, thereby not constituting a limiting performance factor for MPs’ optimal flocculation and aggregation. Even considering exceptionally high concentrations of MPs (2 g/ L) that far exceed naturally-occurring concentrations, the BC hydrogel was shown to have elevated MPs floc culation activity (reaching 88.6%: 1.77 g/L). The computation of bioflocculation activity showed high reliability in predicting flocculation performance, unveiling that the BC:MPs ratio and grinding times were the most critical variables modulating flocculation rates. Also, short exposure times (5 min) were sufficient to drive robust particle aggregation. The microporous nature of the hydrogel revealed by electron microscopy is the likely driver of strong MPs bioflocculant activity, far outperforming dispersive commercial bioflocculants like xanthan gum and alginate. This pilot study provides convincing evidence that even BC remainings can be used to produce highly potent and circular bioflocculators of MPs, with prospective application in the wastewater treatment industry
- Efficacy of bacterial cellulose hydrogel in microfiber removal from contaminated waters: A sustainable approach to wastewater treatmentPublication . Rodrigues, Filipa; Faria, Marisa; Mendonça, Ivana; Sousa, Edward; Ferreira, Artur; Cordeiro, NereidaMicrofibers (MFs), the dominant form of microplastics in ecosystems, pose a significant environmental risk due to the inadequacy of existing wastewater treatments to remove them. Recognising the need to develop sus tainable solutions to tackle this environmental challenge, this research aimed to find an eco-friendly solution to the pervasive problem of MFs contaminating water bodies. Unused remnants of bacterial cellulose (BC) were ground to form a hydrogel-form of bacterial cellulose (BCH) and used as a potential bioflocculant for poly acrylonitrile MFs. The flocculation efficiency was evaluated across various operational and environmental fac tors, employing response surface methodology computational modelling to elucidate and model their impact on the process. The results revealed that the BCH:MFs ratio and mixing intensity were key factors in flocculation efficiency, with BCH resilient across a range of environmental conditions, achieving a 93.6 % average removal rate. The BCH's strong retention of MFs released only 8.3 % of the MFs, after a 24-hour wash, and the flocculation tests in contaminated wastewater and chlorinated water yielded 89.3 % and 86.1 % efficiency, respectively. Therefore, BCH presents a viable, sustainable, and effective approach for removing MFs from MFs-contaminated water, exhibiting exceptional flocculation performance and adaptability. This pioneer study using BCH as a bioflocculant for MFs removal sets a new standard in sustainable wastewater treatment, catalysing research on fibrous pollutant mitigation for environmental protection.
- «
- 1 (current)
- 2
- 3
- »